View TDA1517ATW_3700128.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

d a t a sh eet product speci?cation supersedes data of 2001 feb 14 file under integrated circuits, ic01 2001 apr 17 integrated circuits TDA1517ATW 8 w btl or 2 4 w se power amplifier
2001 apr 17 2 philips semiconductors product speci?cation 8 w btl or 2 4 w se power ampli?er TDA1517ATW features requires very few external components flexibility in use: mono bridge-tied load (btl) and stereo single-ended (se); it should be noted that in stereo applications the outputs of both amplifiers are in opposite phase high output power low offset voltage at output (important for btl) fixed gain good ripple rejection mode select switch (operating, mute and standby) ac and dc short-circuit safe to ground and v p electrostatic discharge protection thermal protection reverse polarity safe capable of handling high energy on outputs (v p =0v) no switch-on/switch-off plop low thermal resistance. general description the TDA1517ATW is an integrated class-ab output amplifier contained in a plastic heatsink thin shrink small outline package (htssop20). the device is primarily developed for multimedia applications. quick reference data ordering information symbol parameter conditions min. typ. max. unit v p supply voltage 6 12 18 v i orm repetitive peak output current -- 2.5 a i q(tot) total quiescent current - 40 80 ma i stb standby current - 0.1 100 m a se application p o output power thd = 10%; r l =4 w- 4 - w svrr supply voltage ripple rejection r s =0 w 46 -- db a cs channel separation r s =10k w 40 55 - db v n(o) noise output voltage r s =0 w- 50 -m v ? z i ? input impedance 50 -- k w btl application p o output power thd = 10%; r l =8 w- 8 - w svrr supply voltage ripple rejection r s =0 w 50 -- db ?d v oo ? output offset voltage -- 150 mv v n(o)(offset) noise output offset voltage r s =0 w- 70 -m v ? z i ? input impedance 25 -- k w type number package name description version TDA1517ATW htssop20 plastic, heatsink thin shrink small outline package; 20 leads; body width 4.4 mm sot527-1
2001 apr 17 3 philips semiconductors product speci?cation 8 w btl or 2 4 w se power ampli?er TDA1517ATW block diagram handbook, full pagewidth mode mgu303 out1a out1b 15 k w 15 k w x 1 va standby switch v p mute switch standby reference voltage 18 k w 18 k w 2 k w 60 k w mute switch c m c m power stage 8 9 15 v p1 v p2 16 17 not connected 1 2 6 7 14 19 20 mute switch va va 2 k w 60 k w power stage 12 13 4 10 11 sgnd pgnd1 pgnd2 out2a out2b non-inverting input 1 inverting input 2 18 svrr 5 + - + - + - + + - + - 3 TDA1517ATW mute reference voltage input reference voltage fig.1 block diagram.
2001 apr 17 4 philips semiconductors product speci?cation 8 w btl or 2 4 w se power ampli?er TDA1517ATW pinning symbol pin description n.c. 1 not connected n.c. 2 not connected in1+ 3 non-inverting input 1 sgnd 4 signal ground svrr 5 supply voltage ripple rejection n.c. 6 not connected n.c. 7 not connected out1a 8 output 1a out1b 9 output 1b pgnd1 10 power ground 1 pgnd2 11 power ground 2 out2a 12 output 2a out2b 13 output 2b n.c. 14 not connected v p1 15 supply voltage 1 v p2 16 supply voltage 2 mode 17 mode select switch in2 - 18 inverting input 2 n.c. 19 not connected n.c. 20 not connected handbook, halfpage TDA1517ATW mgu302 1 2 3 4 5 6 7 8 9 10 n.c. n.c. in1 + sgnd svrr n.c. n.c. out1a out1b pgnd1 n.c. n.c. in2 - mode v p2 v p1 n.c. out2b out2a pgnd2 20 19 18 17 16 15 14 13 12 11 fig.2 pin configuration. functional description the TDA1517ATW contains two identical amplifiers with differential input stages. this device can be used for bridge-tied load (btl) or single-ended (se) applications. the gain of each amplifier is fixed at 20 db. a special feature of this device is the mode select switch. since this pin has a very low input current (<40 m a), a low cost supply switch can be used. with this switch the TDA1517ATW can be switched into three modes: standby: low supply current mute: input signal suppressed operating: normal on condition.
2001 apr 17 5 philips semiconductors product speci?cation 8 w btl or 2 4 w se power ampli?er TDA1517ATW limiting values in accordance with the absolute maximum rating system (iec 60134). thermal characteristics dc characteristics v p = 12 v; t amb =25 c; measured in fig.3; unless otherwise speci?ed. note 1. the circuit is dc adjusted at v p = 6 to 18 v and ac operating at v p = 8.5 to 18 v. symbol parameter conditions min. max. unit. v p supply voltage - 18 v v psc ac and dc short-circuit-safe voltage - 18 v v rp reverse polarity voltage - 6v erg o energy handling capability at outputs v p =0v - 200 mj i osm non-repetitive peak output current - 4a i orm repetitive peak output current - 2.5 a p tot total power dissipation - 5w t vj virtual junction temperature - 150 c t stg storage temperature - 55 +150 c t amb ambient temperature - 40 +85 c symbol parameter conditions value unit tbf -- symbol parameter conditions min. typ. max. unit supply v p supply voltage note 1 6.0 12 18 v i q quiescent current r l = - 40 80 ma operating condition v mode(oper) mode switch voltage level 8.5 - v p v i mode(oper) mode switch current v mode =12v - 15 40 m a v o dc output voltage - 5.7 - v ?d v oo ? dc output offset voltage -- 150 mv mute condition v mode(mute) mode switch voltage level 3.3 - 6.4 v v o dc output voltage - 5.7 - v ?d v oo ? dc output offset voltage -- 150 mv standby condition v mode(stb) mode switch voltage level 0 - 2v i stb standby current - 0.1 100 m a
2001 apr 17 6 philips semiconductors product speci?cation 8 w btl or 2 4 w se power ampli?er TDA1517ATW ac characteristics v p = 12 v; f = 1 khz; t amb =25 c; unless otherwise speci?ed. symbol parameter conditions min. typ. max. unit se application; note 1 p o output power note 2 thd = 1% 2.5 3.3 - w thd = 10% 3 4 - w thd total harmonic distortion p o =1w - 0.1 - % f ro(l) low frequency roll-off - 1 db; note 3 - 25 - hz f ro(h) high frequency roll off - 1db 20 -- khz g v voltage gain 19 20 21 db ?d g v ? channel balance -- 1db svrr supply voltage ripple rejection note 4 on 46 -- db mute 46 -- db standby 80 -- db ? z i ? input impedance 50 60 75 k w v n(o)(rms) noise output voltage (rms value) note 5 on; r s =0 w- 50 -m v on; r s =10k w- 70 100 m v mute; note 6 - 50 -m v a cs channel separation r s =10k w 40 55 - db v o(mote) output voltage in mute note 7 -- 2mv btl application; note 8 p o output power note 2 thd = 1% 5 6.6 - w thd = 10% 6.5 8.0 - w thd total harmonic distortion p o =1w - 0.03 - % f ro(l) low frequency roll-off - 1 db; note 3 - 25 - hz f ro(h) high frequency roll off - 1db 20 -- khz g v voltage gain 25 26 27 db svrr supply voltage ripple rejection note 4 on 50 -- db mute 50 -- db standby 80 -- db ? z i ? input impedance 25 30 38 k w v n(o)(rms) noise output voltage (rms value) note 5 on; r s =0 w- 70 -m v on; r s =10k w- 100 200 m v mute; note 6 - 60 -m v v o(mute) output voltage in mute note 7 -- 2mv
2001 apr 17 7 philips semiconductors product speci?cation 8 w btl or 2 4 w se power ampli?er TDA1517ATW notes to the characteristics 1. r l =4 w , measured in fig.4. 2. output power is measured directly at the output pins of the ic. 3. frequency response externally fixed. 4. v ripple =v ripple(max) = 2 v (p-p); r s =0 w . 5. noise voltage measured in a bandwidth of 20 hz to 20 khz. 6. noise output voltage independent of r s . 7. v i =v i(max) = 1 v (rms). 8. r l =8 w , measured in fig.3. application information handbook, full pagewidth mgu304 15 41011 16 8 + out - out pgnd sgnd 9 100 nf 1000 m f r l 8 w v cc TDA1517ATW 15 k w 10 k w 8.2 k w 15 k w 12 13 + in1 3 18 17 mode 5 470 nf a r i 60 k w b v cc v cc standby/ mute logic micro- controller m c1 m c2 m c1 0 0 1 on mute standby m c2 0 1 0 short circuit and temperature protection input reference voltage r i 60 k w fig.3 btl application block diagram.
2001 apr 17 8 philips semiconductors product speci?cation 8 w btl or 2 4 w se power ampli?er TDA1517ATW handbook, full pagewidth mgu305 15 41011 16 8 + out - out pgnd sgnd 9 100 nf 1000 m f r l 4 w v cc TDA1517ATW 15 k w 10 k w 8.2 k w 15 k w 100 m f 1000 m f r l 4 w 1000 m f 12 13 in1 + 3 18 17 mode 5 220 nf a r i 60 k w in2 - 220 nf b v cc v cc standby/ mute logic micro- controller m c1 m c2 m c1 0 0 1 on mute standby m c2 0 1 0 short circuit and temperature protection input reference voltage r i 60 k w fig.4 se application block diagram. test conditions t amb =25 c; unless otherwise specified: v p = 12 v, btl application, f = 1 khz, r l =8 w , fixed gain = 26 db, audio band-pass: 22 hz to 22 khz. in the figures as a function of frequency a band-pass of 10 hz to 80 khz was applied. the btl application block diagram is shown in fig.3. the pcb layout [which accommodates both the mono (btl) and stereo (single-ended) application] is shown in fig.6. printed-circuit board (pcb) layout and grounding for high system performance levels certain grounding techniques are imperative. the input reference grounds have to be tied to their respective source grounds and must have separate traces from the power ground traces; this will separate the large (output) signal currents from interfering with the small ac input signals. the small signal ground traces should be located physically as far as possible from the power ground traces. supply and output traces should be as wide as possible for delivering maximum output power. proper supply bypassing is critical for low noise performance and high power supply rejection. the respective capacitor locations should be as close as possible to the device and grounded to the power ground. decoupling the power supply also prevents unwanted oscillations. for suppressing higher frequency transients (spikes) on the supply line a capacitor with low esr (typical 0.1 m f) has to be placed as close as possible to the device. for suppressing lower frequency noise and ripple signals, a large electrolytic capacitor (e.g. 1000 m f or greater) must be placed close to the ic. in single-ended (stereo) application a bypass capacitor connected to pin svr reduces the noise and ripple on the midrail voltage. for good thd and noise performance a low esr capacitor is recommended. input con?guration it should be noted that the dc level of the input pins is approximately 2.1 v; a coupling capacitor is therefore necessary.
2001 apr 17 9 philips semiconductors product speci?cation 8 w btl or 2 4 w se power ampli?er TDA1517ATW the formula for the cut-off frequency at the input is as follows: thus as can be seen it is not necessary to use high capacitor values for the input; so the delay during switch-on, which is necessary for charging the input capacitors, can be minimized. this results in a good low frequency response and good switch-on behaviour. in stereo applications (single-ended) coupling capacitors on both input and output are necessary. it should be noted that the outputs of both amplifiers are in opposite phase. built-in protection circuits the ic contains two types of protection circuits: short-circuits the outputs to ground, the supply to ground and across the load: short-circuit is detected and controlled by a soar protection circuit thermal shut-down protection: the junction temperature is measured by a temperature sensor. thermal foldback is activated at a junction temperature of >150 c. output power the output power as a function of supply voltage has been measured on the output pins and at thd = 10%. the maximum output power is limited by the maximum allowable power dissipation and the maximum available output current, 2.5 a repetitive peak current. supply voltage ripple rejection the svrr has been measured without an electrolytic capacitor on pin 5 and at a bandwidth of 10 hz to 80 khz. the curves for operating and mute condition (respectively) were measured with r source =0 w . only in single-ended applications is an electrolytic capacitor (e.g. 100 m f) on pin 5 necessary to improve the svrr behaviour. headroom a typical music cd requires at least 12 db (is factor 15.85) dynamic headroom (compared with the average power output) for passing the loudest portions without distortion. the following calculation can be made for this application at v p = 12 v and r l =8 w : p o at thd = 0.1% is approximately 5 w (see fig.7). average listening level without any distortion yields: the power dissipation can be derived from fig.11 for 0 db and 12 db headroom. table 1 power rating thus for the average listening level (music power) a power dissipation of 2.0 w can be used for the thermal pcb calculation; see section thermal behaviour (pcb design considerations). mode pin for the 3 functional modes: standby, mute and operate, the mode pin can be driven by a 3-state logic output stage, e.g. a microcontroller with some extra components for dc-level shifting; see fig.10 for the respective dc levels. standby mode is activated by a low dc level between 0 and 2 v. the power consumption of the ic will be reduced to <0.12 mw. mute mode is activated by a dc level between 3.3 and 6.4 v. the outputs of the amplifier will be muted (no audio output); however the amplifier is dc biased and the dc level of the output pins stays at half the supply voltage. the input coupling capacitors are charged when in mute mode to avoid pop-noise. the ic will be in the operating condition when the voltage at pin mode is between 8.5 v and v cc . switch-on/switch-off to avoid audible plops during switch-on and switch-off of the supply voltage, the mode pin has to be set in standby condition (v cc level) before the voltage is applied (switch-on) or removed (switch-off). the input and svrr capacitors are smoothly charged during mute mode. the turn-on and turn-off time can be influenced by an rc-circuit connected to the mode pin. switching the device or the mode pin rapidly on and off may cause click and pop noise. this can be prevented by proper timing on the mode pin. further improvement in the btl application can be obtained by connecting an electrolytic capacitor (e.g. 100 m f) between the svrr pin and signal ground. f ic 1 2 p r i c i ------------------------------ = f ic 1 2 p 30 10 3 C 470 10 9 C ------------------------------------------------------------------------------ 11 hz == rating headroom power dissipation p o =5w (thd = 0.1%) 0 db 3.5 w 12 db 2.0 w p all p tot factor ---------------- - 5 15.85 -------------- - 315 mw ===
2001 apr 17 10 philips semiconductors product speci?cation 8 w btl or 2 4 w se power ampli?er TDA1517ATW thermal behaviour (pcb design considerations) the typical thermal resistance [r th(j-a) ] of the ic in the htssop20 package is 37 k/w if the ic is soldered on a printed-circuit board with double sided 35 m m copper with a minimum area of approximately 30 cm 2 . the actual usable thermal resistance depends strongly on the mounting method of the device on the printed-circuit board, the soldering method and the area and thickness of the copper on the printed-circuit board. the bottom heat-spreader of the ic has to be soldered efficiently on the thermal land of the copper area of the printed-circuit board using the re-flow solder technique. a number of thermal vias in the thermal land provide a thermal path to the opposite copper site of the printed-circuit board. the size of the surface layers should be as large as needed to dissipate the heat. the thermal vias (0.3 mm ? ) in the thermal land should not use web construction techniques, because those will have high thermal resistance; continuous connection completely around the via-hole is recommended. for a maximum ambient temperature of 60 c the following calculation can be made: for the application at v p = 12 v and r l =8 w the (all-) music power dissipation approximately 2.0 w; t j(max) =t amb +p r th(j-a) =60 c + 2.0 37 = 134 c. note: the above calculation holds for application at average listening level music output signals. applying (or testing) with sine wave signals will produce approximately twice the music power dissipation; at worst case condition this can activate the maximum temperature protection. handbook, full pagewidth 60 50 40 30 20 10 0 k/w 1 0 number of 35 m m copper layers 234 cu-layer 2-4 mgu306 l l on-board-cooling copper design cu-layer 1 r th(j-a) r th(j-p) fig.5 thermal resistance of the htssop20 mounted on printed-circuit board. r th(j-p) curve is given for practical calculation purpose. l = 30 mm plus vias
2001 apr 17 11 philips semiconductors product speci?cation 8 w btl or 2 4 w se power ampli?er TDA1517ATW handbook, full pagewidth mgu312 in1 sept - 2000 in2 - out2 on std by + out1 + v p 100 nf 220 nf 1000 m f 25 v 1000 m f 16 v 100 m f/16 v tda 1517atw top view bottom copper layout top view component layout top view top copper layout fig.6 printed-circuit board layout for btl and se application. for btl applications the two 1000 m f/16 v capacitors must be replaced by 0 w jumpers.
2001 apr 17 12 philips semiconductors product speci?cation 8 w btl or 2 4 w se power ampli?er TDA1517ATW typical performance characteristics for btl application at v p = 12 v and r l =8 w handbook, halfpage 10 1 10 - 1 10 - 2 mgu307 10 - 2 10 - 1 1 thd (%) p o (w) 10 fig.7 thd as a function of p o . handbook, halfpage 10 1 10 - 1 10 - 2 mgu308 10 - 2 10 - 1 1 thd (%) 10 f (khz) 10 2 p o = 1 w fig.8 thd as a function of frequency. handbook, halfpage - 80 - 60 - 40 - 20 0 mgu309 10 - 2 10 - 1 110 f (khz) svrr (db) 10 2 mute fig.9 svrr as a function of frequency. handbook, halfpage 12 4 0810 v o (v) v mode (v) 26 10 1 10 - 1 10 - 2 10 - 3 10 - 4 mgu310 fig.10 v o as a function of v mode .
2001 apr 17 13 philips semiconductors product speci?cation 8 w btl or 2 4 w se power ampli?er TDA1517ATW handbook, halfpage 010 6 0 2 1 3 4 5 2 p (w) 468 p o (w) mgu311 v p = 15 v r l = 16 w v p = 12 v r l = 8 w fig.11 power dissipation as a function of p o . handbook, halfpage 0 2 68 p o (w) 10 12 18 12 10 4 8 6 14 16 v p (v) mgu323 r l = 4 w 8 w 16 w fig.12 p o as a function of v p .
2001 apr 17 14 philips semiconductors product speci?cation 8 w btl or 2 4 w se power ampli?er TDA1517ATW package outline unit a 1 a 2 a 3 b p cd (1) e (2) z (1) d h ell p y w v q references outline version european projection issue date iec jedec eiaj mm 0.15 0.05 0.95 0.80 0.30 0.19 0.20 0.09 6.6 6.4 4.3 4.1 e h h e 3.1 2.9 4.5 4.3 0.65 6.6 6.2 0.5 0.2 8 0 o o 0.13 0.1 0.2 1.0 dimensions (mm are the original dimensions) notes 1. plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 sot527-1 99-11-12 00-07-12 w m b p d d h e h z heathsink side e 0.25 110 20 11 q a a 1 a 2 l p detail x l (a ) 3 h e e c v m a x a y 0 2.5 5 mm scale htssop20: plastic, heatsink thin shrink small outline package; 20 leads; body width 4.4 mm sot527-1 a max. 1.10 pin 1 index
2001 apr 17 15 philips semiconductors product speci?cation 8 w btl or 2 4 w se power ampli?er TDA1517ATW soldering introduction to soldering surface mount packages this text gives a very brief insight to a complex technology. a more in-depth account of soldering ics can be found in our data handbook ic26; integrated circuit packages (document order number 9398 652 90011). there is no soldering method that is ideal for all surface mount ic packages. wave soldering can still be used for certain surface mount ics, but it is not suitable for fine pitch smds. in these situations reflow soldering is recommended. re?ow soldering reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. several methods exist for reflowing; for example, convection or convection/infrared heating in a conveyor type oven. throughput times (preheating, soldering and cooling) vary between 100 and 200 seconds depending on heating method. typical reflow peak temperatures range from 215 to 250 c. the top-surface temperature of the packages should preferable be kept below 220 c for thick/large packages, and below 235 c for small/thin packages. wave soldering conventional single wave soldering is not recommended for surface mount devices (smds) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. to overcome these problems the double-wave soldering method was specifically developed. if wave soldering is used the following conditions must be observed for optimal results: use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave. for packages with leads on two sides and a pitch (e): C larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board; C smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. the footprint must incorporate solder thieves at the downstream end. for packages with leads on four sides, the footprint must be placed at a 45 angle to the transport direction of the printed-circuit board. the footprint must incorporate solder thieves downstream and at the side corners. during placement and before soldering, the package must be fixed with a droplet of adhesive. the adhesive can be applied by screen printing, pin transfer or syringe dispensing. the package can be soldered after the adhesive is cured. typical dwell time is 4 seconds at 250 c. a mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. manual soldering fix the component by first soldering two diagonally-opposite end leads. use a low voltage (24 v or less) soldering iron applied to the flat part of the lead. contact time must be limited to 10 seconds at up to 300 c. when using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 c.
2001 apr 17 16 philips semiconductors product speci?cation 8 w btl or 2 4 w se power ampli?er TDA1517ATW suitability of surface mount ic packages for wave and re?ow soldering methods notes 1. all surface mount (smd) packages are moisture sensitive. depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). for details, refer to the drypack information in the data handbook ic26; integrated circuit packages; section: packing methods . 2. these packages are not suitable for wave soldering as a solder joint between the printed-circuit board and heatsink (at bottom version) can not be achieved, and as solder may stick to the heatsink (on top version). 3. if wave soldering is considered, then the package must be placed at a 45 angle to the solder wave direction. the package footprint must incorporate solder thieves downstream and at the side corners. 4. wave soldering is only suitable for lqfp, tqfp and qfp packages with a pitch (e) equal to or larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. 5. wave soldering is only suitable for ssop and tssop packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. package soldering method wave reflow (1) bga, hbga, lfbga, sqfp, tfbga not suitable suitable hbcc, hlqfp, hsqfp, hsop, htqfp, htssop, hvqfn, sms not suitable (2) suitable plcc (3) , so, soj suitable suitable lqfp, qfp, tqfp not recommended (3)(4) suitable ssop, tssop, vso not recommended (5) suitable
2001 apr 17 17 philips semiconductors product speci?cation 8 w btl or 2 4 w se power ampli?er TDA1517ATW data sheet status notes 1. please consult the most recently issued data sheet before initiating or completing a design. 2. the product status of the device(s) described in this data sheet may have changed since this data sheet was published. the latest information is available on the internet at url http://www.semiconductors.philips.com. data sheet status (1) product status (2) definitions objective data development this data sheet contains data from the objective specification for product development. philips semiconductors reserves the right to change the speci?cation in any manner without notice. preliminary data quali?cation this data sheet contains data from the preliminary specification. supplementary data will be published at a later date. philips semiconductors reserves the right to change the speci?cation without notice, in order to improve the design and supply the best possible product. product data production this data sheet contains data from the product specification. philips semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. changes will be communicated according to the customer product/process change noti?cation (cpcn) procedure snw-sq-650a. definitions short-form specification ? the data in a short-form specification is extracted from a full data sheet with the same type number and title. for detailed information see the relevant data sheet or data handbook. limiting values definition ? limiting values given are in accordance with the absolute maximum rating system (iec 60134). stress above one or more of the limiting values may cause permanent damage to the device. these are stress ratings only and operation of the device at these or at any other conditions above those given in the characteristics sections of the specification is not implied. exposure to limiting values for extended periods may affect device reliability. application information ? applications that are described herein for any of these products are for illustrative purposes only. philips semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. disclaimers life support applications ? these products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. philips semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify philips semiconductors for any damages resulting from such application. right to make changes ? philips semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. philips semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.
2001 apr 17 18 philips semiconductors product speci?cation 8 w btl or 2 4 w se power ampli?er TDA1517ATW notes
2001 apr 17 19 philips semiconductors product speci?cation 8 w btl or 2 4 w se power ampli?er TDA1517ATW notes
? philips electronics n.v. sca all rights are reserved. reproduction in whole or in part is prohibited without the prior written consent of the copyright owne r. the information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. no liability will be accepted by the publisher for any consequence of its use. publication thereof does not con vey nor imply any license under patent- or other industrial or intellectual property rights. internet: http://www.semiconductors.philips.com 2001 72 philips semiconductors C a worldwide company for all other countries apply to: philips semiconductors, marketing communications, building be-p, p.o. box 218, 5600 md eindhoven, the netherlands, fax. +31 40 27 24825 argentina: see south america australia: 3 figtree drive, homebush, nsw 2140, tel. +61 2 9704 8141, fax. +61 2 9704 8139 austria: computerstr. 6, a-1101 wien, p.o. box 213, tel. +43 1 60 101 1248, fax. +43 1 60 101 1210 belarus: hotel minsk business center, bld. 3, r. 1211, volodarski str. 6, 220050 minsk, tel. +375 172 20 0733, fax. +375 172 20 0773 belgium: see the netherlands brazil: see south america bulgaria: philips bulgaria ltd., energoproject, 15th floor, 51 james bourchier blvd., 1407 sofia, tel. +359 2 68 9211, fax. +359 2 68 9102 canada: philips semiconductors/components, tel. +1 800 234 7381, fax. +1 800 943 0087 china/hong kong: 501 hong kong industrial technology centre, 72 tat chee avenue, kowloon tong, hong kong, tel. +852 2319 7888, fax. +852 2319 7700 colombia: see south america czech republic: see austria denmark: sydhavnsgade 23, 1780 copenhagen v, tel. +45 33 29 3333, fax. +45 33 29 3905 finland: sinikalliontie 3, fin-02630 espoo, tel. +358 9 615 800, fax. +358 9 6158 0920 france: 7 - 9 rue du mont valrien, bp317, 92156 suresnes cedex, tel. +33 1 4728 6600, fax. +33 1 4728 6638 germany: hammerbrookstra?e 69, d-20097 hamburg, tel. +49 40 2353 60, fax. +49 40 2353 6300 hungary: philips hungary ltd., h-1119 budapest, fehervari ut 84/a, tel: +36 1 382 1700, fax: +36 1 382 1800 india: philips india ltd, band box building, 2nd floor, 254-d, dr. annie besant road, worli, mumbai 400 025, tel. +91 22 493 8541, fax. +91 22 493 0966 indonesia: pt philips development corporation, semiconductors division, gedung philips, jl. buncit raya kav.99-100, jakarta 12510, tel. +62 21 794 0040 ext. 2501, fax. +62 21 794 0080 ireland: newstead, clonskeagh, dublin 14, tel. +353 1 7640 000, fax. +353 1 7640 200 israel: rapac electronics, 7 kehilat saloniki st, po box 18053, tel aviv 61180, tel. +972 3 645 0444, fax. +972 3 649 1007 italy: philips semiconductors, via casati, 23 - 20052 monza (mi), tel. +39 039 203 6838, fax +39 039 203 6800 japan: philips bldg 13-37, kohnan 2-chome, minato-ku, tokyo 108-8507, tel. +81 3 3740 5130, fax. +81 3 3740 5057 korea: philips house, 260-199 itaewon-dong, yongsan-ku, seoul, tel. +82 2 709 1412, fax. +82 2 709 1415 malaysia: no. 76 jalan universiti, 46200 petaling jaya, selangor, tel. +60 3 750 5214, fax. +60 3 757 4880 mexico: 5900 gateway east, suite 200, el paso, texas 79905, tel. +9-5 800 234 7381, fax +9-5 800 943 0087 middle east: see italy netherlands: postbus 90050, 5600 pb eindhoven, bldg. vb, tel. +31 40 27 82785, fax. +31 40 27 88399 new zealand: 2 wagener place, c.p.o. box 1041, auckland, tel. +64 9 849 4160, fax. +64 9 849 7811 norway: box 1, manglerud 0612, oslo, tel. +47 22 74 8000, fax. +47 22 74 8341 pakistan: see singapore philippines: philips semiconductors philippines inc., 106 valero st. salcedo village, p.o. box 2108 mcc, makati, metro manila, tel. +63 2 816 6380, fax. +63 2 817 3474 poland : al.jerozolimskie 195 b, 02-222 warsaw, tel. +48 22 5710 000, fax. +48 22 5710 001 portugal: see spain romania: see italy russia: philips russia, ul. usatcheva 35a, 119048 moscow, tel. +7 095 755 6918, fax. +7 095 755 6919 singapore: lorong 1, toa payoh, singapore 319762, tel. +65 350 2538, fax. +65 251 6500 slovakia: see austria slovenia: see italy south africa: s.a. philips pty ltd., 195-215 main road martindale, 2092 johannesburg, p.o. box 58088 newville 2114, tel. +27 11 471 5401, fax. +27 11 471 5398 south america: al. vicente pinzon, 173, 6th floor, 04547-130 s?o paulo, sp, brazil, tel. +55 11 821 2333, fax. +55 11 821 2382 spain: balmes 22, 08007 barcelona, tel. +34 93 301 6312, fax. +34 93 301 4107 sweden: kottbygatan 7, akalla, s-16485 stockholm, tel. +46 8 5985 2000, fax. +46 8 5985 2745 switzerland: allmendstrasse 140, ch-8027 zrich, tel. +41 1 488 2741 fax. +41 1 488 3263 taiwan: philips semiconductors, 5f, no. 96, chien kuo n. rd., sec. 1, taipei, taiwan tel. +886 2 2134 2451, fax. +886 2 2134 2874 thailand: philips electronics (thailand) ltd., 60/14 moo 11, bangna trad road km. 3, bagna, bangkok 10260, tel. +66 2 361 7910, fax. +66 2 398 3447 turkey: yukari dudullu, org. san. blg., 2.cad. nr. 28 81260 umraniye, istanbul, tel. +90 216 522 1500, fax. +90 216 522 1813 ukraine : philips ukraine, 4 patrice lumumba str., building b, floor 7, 252042 kiev, tel. +380 44 264 2776, fax. +380 44 268 0461 united kingdom: philips semiconductors ltd., 276 bath road, hayes, middlesex ub3 5bx, tel. +44 208 730 5000, fax. +44 208 754 8421 united states: 811 east arques avenue, sunnyvale, ca 94088-3409, tel. +1 800 234 7381, fax. +1 800 943 0087 uruguay: see south america vietnam: see singapore yugoslavia: philips, trg n. pasica 5/v, 11000 beograd, tel. +381 11 3341 299, fax.+381 11 3342 553 printed in the netherlands 753503/02/pp 20 date of release: 2001 apr 17 document order number: 9397 750 08264

▲Up To Search▲

Price & Availability of TDA1517ATW

	To Download TDA1517ATW Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .